Get Them While They're Hot!
Displaying 1 to 15 (of 105 items)
Result Pages: 7
Brand: C.R. Laurence
CRL Adjustable 90 Degree Inside Suction Holder. This CRL Adjustable 90 Degree Inside Suction Holder firmly grips glass from the inside surface at 90 degrees. Height and position can be adjusted up to 5/16 (8 mm) by knobs located on each arm for precise UV adhesive application. Glass pieces are held firmly in place by 2-3/8 (60 mm) diameter rubber suction pads until they are bonded.
$86.00
Buy.com
See More
Brand: C.R. Laurence
CRL Fixed Position 90 Degree Inside Suction Holder. This CRL 90 Degree Inside Suction Holder firmly grips glass from the inside surface at a fixed 90 degree angle. 2-3/8 (60 mm) diameter rubber suction pads hold the glass pieces firmly until they are bonded.
$66.00
Buy.com
See More
Brand: C.R. Laurence
CRL Fixed 90 Degree Interior Corner Clamp. The CRL Fixed 90 Degree Interior Corner Clamp holds inside glass pieces at 90 degrees. Can be used with our Cat. No. UV284 Support to hold glass pieces while bonding. 2-3/8 (60 mm) diameter rubber suction pad holds glass pieces firmly until they are bonded.
$44.00
Buy.com
See More
Brand: C.R. Laurence
CRL Magfix Fixed 90 Degree Magnetic Cube. The CRL Magfix Fixed 90 Degree Magnetic Cube securely holds smaller glass parts up to 3/8 (10 mm) thick at 90 degree angles. The cube is ideal for use in areas with limited space since it measures only 2-7/32 (56 mm) square. Plates measure 1-3/16 x 3-3/16 (30 x 81 mm). Cube and Counter Plates have beveled edges, and are lacquered to avoid scratches on glass surfaces and adhesion of UV Adhesives during application.
$121.00
Buy.com
See More
Brand: C.R. Laurence
CRL 90 Degree Clamp-It Square Tool Kit. CRL 90 Degree Clamp-It Square Tool Kit allows you to align, hold, and clamp glass securely in place while bonding the glass pieces with UV adhesives. It includes everything needed to clamp two corners at a time: two original Clamp-It Assembly Squares and four 5 (127 mm) Clamp-It Bar Clamps. The Bar Clamp is held in place on the Clamp-It Assembly Square with a friction fit to make operation quick, easy, and one-handed.
$70.00
Buy.com
See More
Brand: C.R. Laurence
CRL Battery Operated UV Adhesive Curing Lamp. Our Battery Operated UV Curing Lamp may be small, but when allowed the appropriate initial pre-cure and final curing times, the resulting bonds will be high quality in strength and appearance. Power comes from the four AA batteries included with the Lamp, producing 1,000 watts/cm of light output. This is the most affordable tool to use when starting out with UV bonding on a small scale.
$57.00
Buy.com
See More
Brand: C.R. Laurence
CRL Analog Timed Air Dispenser Kit. CRL Analog Timed Air Dispenser is an economical general purpose dispenser, versatile and simple to use. For operator or automatic use in manual or automatic modes for timed air deposits, dots, beads or potting. Easy to read gauges. Timed air pushes fluid out in doses. Hook up the barrel adapter (included) connect the air and electric cords. Timed air is sent into the syringe to push the material out in measured doses. Complete starter kit, ready to use.
$1067.00
Buy.com
See More
Brand: C.R. Laurence
CRL Heat Guard Stand for Z7596/AUZ7569 UV Curing Lamps. This CRL Heat Guard for Z7596/AUZ7569 Lamps is a stainless-steel, vinyl-coated heat guard/stand that makes lamp operation safer by protecting against accidental burn injury. Special insulators keep it from touching the lamp housing, thus minimizing heat conduction. The Heat Guard helps prevent mechanical shock damage, resulting in substantial savings on bulb and filter replacement costs.
$94.00
Buy.com
See More
Brand: C.R. Laurence
CRL Replacement Bulb for UB80, UV240, and UV240230. This CRL Replacement UV Bulb 4-watt integrally filtered tube fits both the Cat. No. UV240 and Cat. No. UB80 ultraviolet curing lamps.
$17.00
Buy.com
See More
Brand: C.R. Laurence
CRL Replacement 30cc UV Adhesive Syringe. Working with UV adhesives requires carefully control of the volume used for each application. These CRL Syringes work with Cat. No. UV1284 CRL Analog Timed Air Dispenser for an economical general purpose dispense of UV adhesives. Timed air is sent into the syringe to push the material out in measured doses.
$8.00
Buy.com
See More
Brand: C.R. Laurence
CRL Australian Use Double Tube UV Curing Lamp 230 Volts AC 50Hz. The CRL Long Double Tube UV Curing Lamp is perfect for use where high-intensity, wide-area UV coverage is needed. Specially filtered 40 watt bulbs make it the most powerful lamp of it s type available. Suited to cure all CRL UV Bonding Adhesives, it features an enameled sheet metal housing that can be side mounted, hung overhead, or used as a portable lamp to accommodate many different requirements.
$624.00
Buy.com
See More
Brand: C.R. Laurence
CRL Third Hand Fixation Device. The CRL Third Hand Fixation Device is the perfect solution for applying the pressure needed to bond UV and shower door hardware in place during heating and curing. The adjustable steel sliding bracket allows for precise positioning of clamp tips over your hardware. The clamp screws can accommodate knobs or bars exceeding 2 (51 mm) in height.
$79.00
Buy.com
See More
Brand: C.R. Laurence
CRL Replacement Bulb for Double Tube UV Curing Lamp. CRL UV Replacement Bulb for CRL s 40 Watt UV Lamp Cat. No. XX40.
$117.00
Buy.com
See More
Brand: C.R. Laurence
CRL UV Lay-Out Mat. CRL s UV Lay-Out Mat covers a large 24 x 36 (610 x 914 mm) work surface and lets you check your bonding project for square prior to adhesive application. The surface is self-healing should you also use it for razor cutting. Flip it over to the blank side and you have a durable, protective surface for your other work.
$65.00
Buy.com
See More
Brand: C.R. Laurence
CRL UV Hardware Positioning Device. Accurate positioning of UV bonding hardware is essential to producing high quality finished displays, showcases, and furniture. The CRL UV Hardware Positioning Device quickly attaches to the glass with a 2-1/8 (54 mm) suction cup, and features a pivoting arm to align hardware on two surfaces when required. Once in place, the initial adhesion set can be made, the Positioning Device removed, and the final cure can then be completed.
$64.00
Buy.com
See More

« Prev 1 2 3 4 5 6 7 Next »